Expert Answers about Cruiser RV
- Which Solera Power Awning Replacement Motor Fits Awning Made in 2015
- For a 2015 model Solera awning the motor replacement you want is the part # LC266149 that you referenced. We've had customers come back and tell us that they used this motor on a 2015 model awning and it worked well.
view full answer... - How Does Go Power Automatic Transfer Switch # 34270278 Connect to Shore Power and Inverter
- The Go Power Automatic Transfer Switch # 34270278 that you are interested in was designed to automatically switch power sources between an inverter or an AC power source. You'd want to run the inverter you have now to this as well as the power source wiring from shore power and this would automatically take care of your AC power needs/switching. Basically your battery would connect to the inverter, the inverter to the # 34270278 and then the # 34270278 to your fuse panel. This does not...
view full answer... - Will MORryde Shackle Upgrade Kit # MR58ZR Fit 2013 Cruiser RV Funfinder X
- While the shackle straps of the MORryde HD Shackle Upgrade Kit part # MR58ZR are 1/4 inch shorter than the 2-1/2 inch long ones you have now this still work well. The slight length difference won't really affect anything. Your current equalizers wouldn't be an issue either.
view full answer... - Upgrading Base RV Ceiling Vent Fans for Thermostatically Controlled Fans
- Unfortunately there is no way to swap out the basic fans that come in your 2019 Cruiser RV Shadow Cruiser 193 MBS for a thermostatic controlled fan. You will need to replace the entire assembly which will entail removing the caulking and screws on the roof.
I recommend the MaxxFan Deluxe Roof Vent # MA00-07000K as it is one of the only fans that will allow you to operate it during rain as well. It features a 10 speed fan that can run in either direction allowing you to ventilate your...
view full answer... - Should Friction Sway Control be Used with Dual Cam Setup of Strait Line
- The dual cam setup of the Strait Line systems is going to be much more effective than a friction sway bar like you are interested in. Adding a friction sway control device would not stop what you are experiencing. Your best way of fighting the type of sway you are getting would be to get more tongue weight on the trailer as an inadequate amount of tongue weight relative to the total trailer weight is the biggest cause of sway. So if you can move weight forward in the trailer that will be...
view full answer... - Recommended Solera Slide Topper for 94-1/2 Inch Box Width
- The Solera 8 Foot Slider (Slide-Topper) # LCV000168106 referenced in your question is designed for a box width range of 86 inches to 91-3/4 inches. When measuring your box width, you will want to measure from the outside front of the box, including flange. Since your box size with the flange is 94-1/2 inches, this will not be the correct fit.
I instead recommend the 8.5 Foot Solera Slide-Topper # LCV000168107. This will work with a box width range of 92 inches to 97-3/4 inches so it will...
view full answer... - Replacement Brake Assemblies and Bearing Kit for 2012 Cruiser Toyhauler with Dexter 3500 lb Axle
- We have a set of self-adjusting brake assemblies that will fit your Dexter 3,500 lb trailer axles with the part # AKEBRK-35-SA which will work well. This is a set of left and right brake assemblies. Then for a bearing kit all you'd need is the part # BK2-100 which comes with correct bearings and seal.
view full answer... - Upgrading to Lippert Road Armor Suspension on 2019 Cruiser RV MPG 2021RB
- The Road Armor Shock Absorbing Equalizer Kit - Tandem Axle # LC696740 is a great choice for your 2019 Cruiser MPG 2021RB. I have included the measurements of the Road Armor (See picture below) for you to compare with your current setup to ensure a problem free installation. The Lippert AP Kit # LC52SV includes new shackles, wet bolts, and hardware.
view full answer... - Upgrading Dexter Double-Eye Spring 072-020-00
- In order to replace the leaf springs on a trailer you'll need to choose ones that have the same unloaded length from eye to eye. If you go with a set slightly longer or shorter you'd then need to swap out the shackle straps as well to help compensate for the difference in length. The closest we have to 24" is the 6-Leaf Double-Eye Spring part # SP-222275 which will be an upgrade from the Dexter Double-Eye Spring 072-020-00.
However, since it's slightly longer you'd want to use a slightly...
view full answer... - Slide-Topper for a 2018 Cruiser RV Fun Finder Xtreme Lite Travel Trailer
- Yes, the Solera 8.5' Slider (Slide-Topper) part # LCV000168107 is correct for your 2018 Cruiser RV Fun Finder Xtreme Lite Travel Trailer with a 96" flange to flange measurement. This slide-topper comes in black and the awning rail is included. This will be the best option for you. It is made in the U.S.A. and comes with a one year warranty.
view full answer... - Can Trailer Hitch be Installed on 2019 Shadow Cruiser Travel Trailer
- You should be able to install the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" - 72" Wide # 13703 on your 2019 Shadow Cruiser travel trailer. We haven't test fit this so I can't guarantee this will fit but if you have room for a trailer hitch and your trailer frame is within the 22" - 72" width range of this product then this is the trailer hitch that I recommend. This hitch can be a bolt-on or a weld-on installation.
I have attached the installation instructions for you to...
view full answer... - Cargo Carrier and Bike Rack Solution that Can be Used with Fun Finder Travel Trailer
- The Hollywood Racks Sport Rider SE2 Platform Bike Rack w/ Cargo Carrier # HR1450Z-85 that you referenced can be used in the trailer hitch of your truck but it's not rated for use at the rear of a camper like your Fun Finder as the ride quality there will be much rougher.
The closest bike rack solution we have then is the reinforced Swagman Dispatch part # S44FR which you'd use at the rear of the camper and then the A-frame platform # CC-255 would be a great choice to carry cargo above...
view full answer... - Options for Sway Control Tab for Ball Mount for Attaching Hitch Ball
- Sounds like you are looking for the mount for the small ball of your friction sway control unit. You have a couple options like the part # D320 which is a ball mount that has the mounting tab attached to the side of the ball mount platform. We have the # 3442 which allows you to weld a tab onto your current ball mount, or we have the # RP26003 which fits between the ball mount platform and the hitch ball.
view full answer... - Recommended Bright LED Floodlights for Rear of Horse Trailer
- We have the perfect solution for you.
I'd recommend going with two of the Buyers Products low profile LED floodlights, part # 3371492135. The lamp is pretty small, so if you have some room between the top of the rear door and the roof you could easily fit two of the 5-3/4 x 2-1/2 inch lamps in that space. If there's not enough room there you could mount the lamps on the sides of the trailer, up toward the top which would also work great for you.
Each lamp puts out about 1600 lumens, so...
view full answer... - Equalizer Upgrade Kit for 2020 Shadow Cruiser 193MBS
- When choosing an upgraded equalizer like the Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2 # LC696740 you want to choose a kit that is as close as possible to your current equalizer width. The # LC696740 measures 6" from center to center across.
I recommend measuring your current equalizers in order to make the best choice. If your current equalizers share the same 6" measurement, or are very close, then this kit will work well for you.
This is the only size available...
view full answer... - Will Reese Steadi-Flex #RP66560 or Equal-i-zer Weight Distribution System Work Best On Stryker RV?
- The Reese Steadi-Flex Weight Distribution System # RP66560 will work for your 2019 Cruiser RV Stryker travel trailer toy hauler as long as you do not exceed 12,000lbs maximum trailer weight of the hitch. My concern is the 600-1,200lb tongue weight capacity. The 1080lbs of tongue weight is without the additional propane, batteries and any gear on the camper. You will likely exceed that with additional gear.
I do prefer the Equal-i-zer Weight Distribution System # EQ37140ET with your Stryker...
view full answer... - Suspension Enhancement for Stryker 2816 Travel Trailer
- We don't have any air bag kits that are designed for suspension enhancement on trailer but we do have the SumoSprings part # SS26MV which will give the suspension more support. You'd need two of these kits since your trailer is a tandem axle. These are rated for axles that are between 5k and 8k so it would be correct kit for your Stryker 2816 travel trailer.
view full answer... - Recommended 2-5/16 Hitch Ball For Reese Stedi-Flex Weight Distribution Hitch
- I recommend the 2-5/16" Hitch Ball # 63836 to use with the Reese Steadi-Flex Weight Distribution System w/ Sway Control # RP66560. This hitch ball carries the same 14K weight rating as the Stedi-Flex to ensure that you never exceed the weight capacity of a single component.
You will need a 1-7/8" 12pt Thin Walled Socket # ALL643216 to properly install the hitch ball on the Stedi-Flex hitch.
view full answer... - Multi-Fit Hitch that Could be Used on 2020 Cruser MPG 2550RB
- We have the multi fit Curt hitch part # 13703 which is a Class III hitch that can be used at the rear of a travel trailer like your 2020 Cruser MPG 2550 to carry an RV approved bike rack like the Swagman XP part # S64940.
view full answer... - How Tight Does Riveted Nuts of Dual Cam Sway Control Get Tightened
- The set screw of the Dual Cam setup part # RP26002 along with the rivet screws/bolts of this kit hold it in place. You'd want to follow the instructions for the install of the bolts like you see on the attached picture. The rivet screws get secured tightly.
view full answer...
Go To Results